Click Get Details to get more information on a specific product.
You can add the item to your cart or basket from the Details page.
|
|
 |
this windage tray is awesome! for use with 2.4 motors that have removed the balance shafts. Fits both strapped and unstrapped blocks!
If you don't have a drill and tap for the balance shaft oil hole, be sure to order one! fwd pn 104-1310
|
|
|
 |
ARP head stud kit for the srt-4
|
|
|
|
Realtune billet tone wheel
|
|
|
 |
Clevite 77 Main bearing set for the SRT-4. These bearings are the best available for your 2.4 motor. STD size
|
|
|
|
Clevite 77 Main bearing set for the SRT-4. These tri-metal bearings are the best available for your 2.4 motor. .25mm (.010") size
|
|
|
|
Clevite 77 Main bearing set for the SRT-4. These tri-metal bearings are the best available for your 2.4 motor. .50mm (.020") size
|
|
|
 |
Clevite 77 rod bearing set for the SRT-4. These tri-metal bearings are the best available for your 2.4 motor. .50mm (.020") size
|
|
|
|
Clevite 77 bearings are the best available rod bearing for your motor. .25mm oversize, set of 4
|
|
|
|
Clevite 77 bearings are the best available rod bearing for your motor. STD size, set of 4
|
|
|
 |
Custom head gasket from Cometic, maker of the some of the best gaskets made in the USA. This is NOT two stock gaskets rivets toegther like other vendors sell, this is the best head gasket available for the neon 2.4l turbo! .051" thick, and the bore size is good up to .040 or 89mm
|
|
|
|
Steel crank strap kit with ARP studs, washers, and nuts. Requires bedplate to be machined. For 2.4 srt4 motor.
|
|
|
|
Drill bit, tap and plug for the balance shaft hole. When you remove the balance shafts, the oil feed hole must be tapped and plugged. this set has everything needed.
|
|
|
|
eagle rods fort he neon srt-4
.866 pin size, 5.945 lenght H-Beam design
|
|
|
 |
Energy Suspension Motor Mount Insert Kit for Dodge SRT 4 2003-2005. A true high performance motor mount for street use. Soft enough to absorb vibrations but strong enough for racing.
|
|
|
|
Everything you need for a build bottom end. Pistons, std or .020, H-beam rods, bottom end gasket kit, new Oil pump, rod and main bearings. If you plan to go over 500hp, we also recommend our strap kit sold separate.
|
|
|
 |
Factory exhaust manifold gasket
|
|
|
 |
Mopar intake gasket manifold for the srt-4 neon
|
|
|
 |
Oil pan gasket for the neon srt-4
|
|
|
 |
replacement oil pan for the neon srt-4
|
|
|
 |
Melling, OEM manufacturer, oil pump
|
|
|
 |
Race Motot Mount Insert Kit. Fits 2000-2004 Dodge Neon SRT 4. Upper and Lower
|
|
|
|
|
|
|
|
Rear main seal for 2.2/2.5
|
|
|
 |
180 degree thermostat fits Dodge Neon and is a performance thermostat that makes your engine run cooler
|
|
|
|
Complete set of Mahle (oem supplier) piston rings for the 2.4l SRT-4. Comes in STD size only
|
|
|
|
Mopar replacement drain plug for the neon srt-4, PT cruiser
|
|
|
|
Includes 10 m8x1.25 studs/10 nuts
|
|
|
|
Wiseco SRT4 pistons. Forged, STD 87.50mm size. Includes rings, pins and clips
|
|
|
|
Wiseco SRT4 pistons. Forged, .020 oversize 88.00mm size. Includes rings, pins and clips
|
|
|
